| 首页 | 汽车电路图 | 手机电路图 | mp3电路图 | 功放电路图 | 主板电路图 | 显示器电路图 | 电磁炉电路图 | 开关电源电路图 | 电视机电路图 |
| 收音机电路图 | 电源电路图 | 充电器电路图 | 耳机电路图 | 滤波电路 | 遥控器电路图 | usb电路 | 放大电路 | 防盗报警器 | 振荡电路 |
| 控制电路 | 脉冲电路 | 保护电路 | 电话机 | LED电路 | 电饭堡电路 | 热水器电路 | 传感器电路 | 小家电电路 | 温度计 | 电动自行车 |
|
前一个电路图:Quadraphonic Amplifier |
模块化的防盗系统

This circuit features automatic Exit and Entry delays and a timed Bell Cut-off. It has provision for both normally-closed and normally-open contacts, and a 24-hour Personal Attack/Tamper zone. It is connected permanently to the 12-volt supply and its operation is "enabled" by opening SW1. By using the expansion modules, you can add as many zones as you require; some or all of which may be the inertia (shock) sensor type. All the green LEDs should be lighting before you open SW1. You then have up to about a minute to leave the building. As you do so, the Buzzer will sound. It should stop sounding when you shut the door behind you. This indicates that the Exit/Entry loop has been successfully restored within the time allowed. When you re-enter the building you have up to about a minute to move SW1 to the off position. If SW1 is not switched off in time, the relay will energise and sound the main bell. It will ring for up to about 40 minutes. But it can be turned off at any time by SW1. The "Instant" zone has no Entry Delay. If you don't want to use N/O switches, leave out R8, C8 and Q2; and fit a link between Led 3 and C7. The 24 Hour PA/Tamper protection is provided by the SCR/Thyristor. If any of the switches in the N/C loop is opened, R11 will trigger the SCR and the bell will ring. In this case the bell has no time limit. Once the loop is closed again, the SCR may be reset by pressing SW2 and temporarily interrupting the current flow. The basic circuit will be satisfactory in many situations. However, it's much easier to find a fault when the alarm is divided into zones and the control panel can remember which zone has caused the activation. The expansion modules are designed to do this. Although they will work with the existing instant zone, they are intended to replace it. When a zone is activated, its red LED will light and remain lit until the reset button is pressed. All the modules can share a single reset button. The Stripboard layout of the prototype is available.
相关电路图:
电缆测试电路 | 基本RC桥式振荡电路 | |
|
|
||
具有稳幅环节的RC桥式振荡电路 | 2W 音频放大器 | |
|
|
||
4管发射机原理图 | 过零脉冲电路(实验验证过) | |
|
|
||
5.1ch 功放电路 | 5.1c功放系统 | |
|
|
||
7107做的电压表(双表) | IC卡读写器原理图 | |
|
|
||
USB多媒体2.5W+2.5W | 光控、单按键开关壁座电路 | |
|
|
||
几种VI转换和恒流源电路图的比较 | 开关电源式高压恒流源电路图 | |
|
|
||
门铃电路 | 新构思电子保险丝 | |
|
|
||
|
电子技术下载网 | 网站地图 | 联系我们 | 免责声明 | 招聘信息 | 友情链接 Copyright © 2005 - 2007 电子电路网 - 单片机设计网下属站点 |